LH100AY4040XX-XX

Product Specification

Introduction

High power LED high bay light, using high brightness LED chip, high transmission radiator, lamp shade adjusting beam angle. It can be widely used in energy-intensive, large amount electricity, long time using electricity environment, it can solve industrial waste electricity effectively.

Technical Data

Luminance Distribution

Integrating Sphere Test
Illuminance Diagram

LH100AY404008

LH100AY404012

Dimensions
Features
  • Adopts single LED module source design, high thermal conductivity, low lumens depreciation and uniform light colour
  • High PFC, Long lifespan >50000 hours, low carbon and lead free
  • Resistance to fluctuation
  • Protection with short circuit, over current, over voltage and over temperature
  • 100% full capacity aging testing
  • Instant start-up
  • Excellent appearance design, easy installation, easy disassembly, and wide application
    • Application
    Only for indoor use, such as workshop, warehouse, toll station, supermarket, exhibition hall, gymnasium and other indoor illumination places. Not suitable places: Outdoor, High dust, high oil, inflammable or low noise required places.
    Power / Time
    Packaging

    Separately package between LED high bay light body（PART.A）and lamp shade (PART.B).

    PART A :
    30.0×24.5×35.5cm (1pcs/Box)
    50.0×31.5×37.5cm (2Box/ctn)

    80° PART B :
    44.5×44.5×42.0cm (20pcs/ctn)
    120° PART B : 52.5×52.5×29.0cm (20pcs/ctn)

    Installation Method

    Function Indicator Diagram

    Pic.1 Installation Shade

    Pic.2 Installation Hook

    Pic.3 Installation Screws

    1. Installation lamp shade: Firstly loose the screws ①②③④, set the lamp shade hole ③④⑤⑥ correspondingly to the four screws, then spin the lamp shade anticlockwise to assure it, tighten the bolts finally; ( as Pic. 1 )
    2. Installation hook: Screw the hook into hole clockwise ①. ( as Pic. 2 )
    3. Installation the protection screw: Screw M4*16 into hole ②, assure tighten it well. ( as Pic. 3 )
    4. As Pic.4, the installation finished
    Installation Caution
  • Installation should be done by professional electricians.
  • Please make sure all power is turned off before installation completed.
  • Please ensure the power supply wire grounding is normal.
  • Please ensure the hook tighten well.
  • When connecting wires, don’t make any frictions or drop off the product, otherwise will cause damage.
  • Be sure to install the lights correctly, the power cord bare wire must be connected with insulation protection.
  • When connecting wires, should clearly know Neutral wire , Earth wire and Live wire to assure safety. After examination, switch on.
  • Don‘t cover anything on or touch the emitting section and the heat sink during lighting.
  • The luminairies should be positioned so that prolonged staring into the luminaries at a distance closer than 3 m is not expected.
  • Luminaries has two degrees of protection provided: IP65 for LED module part, IP20 for another parts.
    • Power Supply Connection

    Power Supply Connection – Caution

    1. If the Power cord of this luminaries is damaged it must only be replaced by the qualified engineer in order to avoid a hazard.
    2. The light source contained in this luminaires must only be replaced by the
      qualified engineer
      CAUTION – RISK OF ELECTRIC SHOCK
    3. A wiring device shall be provided for connection to a branch circuit. The wiring device shall be rated for the temperature, voltage, and current encountered during normal operation.
      For Example
      — 3 PIN Screw less terminals
      — Rated voltage 250V
      — Rated connecting capacity 1.5-2.5mm2
      — Conductors be tinned
      — If necessary please provide the wiring compartment for the terminal block
    Troubleshooting and Maintenance

    Troubleshooting (only qualified engineers should disassemble the lamp)
    Fault finding and solutions: During inspection, look for any signs of colour changes or damage at the LED source, any obvious breakage of connections, loose power supply connections, any short circuit, any obvious damage condition. Please replace with new LED source or driver if fault found.

    Guarantee Clause

    Product Guarantee

    CIT International guarantee within 5 years from delivering to customers, we will be responsible for repair and replacement, if any conditions such as not bright or flicker of LED source under right preservation, installation, usage and maintenance.

    Disclaimer and Limitation

    1. Under any circumstances, any quality problems compensation should be within the guarantee period.
    2. The product guarantee does not include: Product damage caused by.
      2.1 The negligence of storage, transportation or improper handling.
      2.2 Incorrect operation or not proper usage of product.
      2.3 Any damage caused by repair or modifications from unauthorized person.
      2.4 Caused by the forces of nature, irresistible factors of product damage, such as Earthquakes, typhoons, tornadoes, volcanic eruptions, floods, lightning, heavy snow, war, etc
    3. If the product serial number has been changed, altered or blur, it will no longer enjoy the corresponding guarantee.
    4. This guarantee is not responsible for repair or replacement of the transport, customs clearance fee.

    Remark

    Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
    LED High Bay neustále vývíjíme a parametry uvedené v tabulkách se mohou bez předchozího upozornění měnit. Pro aktuální parametry a ceny kontaktujte CIT International.